50,000+ Bearings | 50-90% Under Distributor Price | Same Day Free Shipping

Tapered Roller Bearing Cone and Cup: Match the Pair

Tapered roller bearing cone LM11949 and cup LM11910 make one bearing
How tapered roller bearing cone and cup part numbers pair up: read LM11949/LM11910, decode the prefix and order the right set the first time.

A tapered roller bearing set is two parts with two part numbers. Order one and you’ve bought half a bearing.

How tapered roller bearing cone and cup numbers pair up, and how to order the right set the first time.

A wheel hub, a gearbox shaft, a conveyor pulley. The old bearing comes out in pieces, someone reads one number off one ring, and the order goes in.

Two days later the box shows up. It’s a cone. The cup is still in the housing, scored and blue.

That’s the whole trap. Tapered roller bearings are sold as a cone and a cup, and each one carries its own number. Here’s how to read them and match the pair. Inch or Metric.

Box with only a cone delivered while the worn cup is still in the housing

Cone, Cup, Set: Three Numbers for One Bearing

Start with the anatomy.

  • The cone is the inner ring, the rollers and the cage, assembled together. It sits on the shaft.
  • The cup is the outer ring. It’s pressed into the housing.
  • The set is a cone and a matching cup, sold together under one assembly number.

Take LM11949/LM11910, one of the most common tapered roller bearing cone and cup pairs in the world. LM11949 is the cone, with a 19.05 mm (0.75 in) bore. LM11910 is the cup, with a 45.237 mm outside diameter. Write them together with a slash and you’ve described one complete bearing.

Set numbers add a shortcut. L44649/L44610 is widely sold as SET4, for example. Handy at the counter. Less handy when the box says one thing and the drawing says another.

“The number’s on the bearing, just order that” is what the parts counter says. “Which ring did you read?” is the question that matters.

What the Letters and Digits Mean

Inch tapered roller numbers follow the ABMA system, which nearly every major maker uses. That’s why the same LM11949 shows up from Timken, SKF, Koyo, NTN and others.

  • The prefix is the duty class. From light to heavy: EL, LL, L, LM, M, HM, H, HH, EH. LM is light-medium. HM is heavy-medium.
  • The middle digits identify the series. In LM11949 and LM11910, the shared “119” is your clue they belong to the same family.
  • The last two digits split cone from cup. As a rule of thumb, cone numbers end in the 30s and 40s (49, 48, 43). Cup numbers end in the 10s (10, 11, 12).
  • Suffixes change details. A, B, or other letters can mean a different width, rib, chamfer or angle. Treat a suffix as part of the number, not decoration.

One series can have several cones that fit the same cup, and several cups that fit the same cone. L44643 and L44649 share the L44610 cup, with different bores. That’s why matching the family matters more than matching a single digit.

There are many storeroom bins with a dozen cones and no cups or vice versa.

How to read a tapered roller bearing cone and cup part number

Why the Pair Matters More Than the Brand

A tapered roller bearing cone and cup are ground to work together: the roller angle on the cone has to meet the raceway angle on the cup. Get the family right and brand rarely matters. Get the family wrong and no brand will save it.

That’s also why surplus works so well for tapers. Plants buy cones and cups by the case, use a few, and the rest stay new in the box for years. Same ABMA numbers, same fit, a fraction of the price.

Metric Tapers Work Differently

Metric tapered roller bearings, like the 30205 or 32008, usually ship as one part number for the complete bearing. No cone/cup split on the order.

Mixing the two systems is the other common mistake. A metric 30205 and an inch set with a similar bore are not interchangeable. Measure the bore, OD and width, and check whether the shaft was ever inch or metric to begin with.

How to Order the Right Tapered Roller Bearing Cone and Cup

  1. Read both rings.
    • The cone number is stamped on the large rib face or the cage.
    • The cup number is stamped on the outer ring face.
    • Can’t read it? Measure bore, OD and cup width with calipers.
  2. Decide: set, cone only, or cup only.
    • Replacing both is standard practice. A new cone on a worn cup wears fast.
    • If the cup is still good and staying in the housing, order the cone alone.
    • Order by the full pair, written as cone/cup, so nothing gets missed.
  3. Buy where the stock is real.

Need help matching a cone to a cup in a hurry? Find your part, and we’ll ship it today.

Cone and cup: always order the pair, 50,000+ bearings in stock

Quick answers

What is the difference between a tapered roller bearing cone and cup?
The cone is the inner ring with rollers and cage. The cup is the outer ring, sometimes named race. Together they make one bearing.

Do I need to replace the cup when I replace the cone?
Usually, yes. A worn cup shortens the life of a new cone. Replace them as a pair unless the cup is in clearly good condition.

Can I mix brands?
Inch tapered roller bearings with the same ABMA number are designed to interchange across major brands. Match the full number, suffix included.

What does a SET number mean?
It’s a shorthand for a specific cone and cup pair, like SET4 for L44649/L44610.

For more on reading numbers under pressure, see how to buy bearings by part number. Match the pair, ship it today.

Need the part now? Make it easy. → Find Your Part

Need help finding the right part?

Our knowledgeable team is here to help!

Row of six overlapping metal ball bearings
Need help finding the right part?

Our team can locate, cross-reference, and source all parts.

Get In Touch
Need help finding the right part?

Our team can locate, cross-reference, and source all parts.

Get In Touch
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.